ROOF COATINGSilicone & Acrylic

A roof coating buys years back on a Sylmar flat roof that is weathered but still sound. Hillside exposure means long afternoon sun and the first of the Santa Ana winds, which is hard on a flat roof's surface and its flashings.

Serving Sylmar and nearby

We coat commercial and residential low-slope roofs throughout Sylmar and the surrounding Los Angeles County communities, including San Fernando, Pacoima and Mission Hills.

Local notes for Sylmar

Roofs in Sylmar do not wear out the way a brochure says they do, and the same three details cause most of the leaks we are called out for. 21 miles northwest means a free inspection costs you nothing but an hour.

We work the same streets in San Fernando, Pacoima and Mission Hills, so crews know the area and its roofs.

• Gutters are pulled and refitted where they block a proper drip edge.
• Access gets planned first - driveway, staging, dumpster placement - so the street stays usable.
• Permits and inspections run through the local building department, and we pull them rather than leaving it to you.
• Tile is sorted and reused where it is sound, which keeps the roof looking original.
• Skylights are re-flashed as part of the job rather than quoted as an extra later.

Summer is for planned work; winter is for emergencies nobody planned. If a repair solves it, we quote the repair instead of selling a replacement.

Our habits on site

The site is cleaned daily, and the last magnet pass happens before the crew leaves.

• Ventilation gets looked at while the roof is open; most Sylmar attics run hotter than they should.
• Most homes take two to four days once material lands.
• Edges are fastened to spec because that is where uplift starts.
• Payment is tied to progress, not demanded up front.

What the work looks like

• Inspect and measure, including core tests where we need to know what is under the membrane
• Clean the roof — power wash, remove dirt, chalk and loose coating
• Repair: cracks, open seams, failed flashing, blisters and bad penetrations
• Prime where the substrate calls for it
• Apply the coating in multiple passes to the specified thickness, seams and details first
• Final walk for even coverage and thickness, then clean up the site

Choosing the system for your Sylmar roof

• Silicone: the pick for roofs that pond. It handles standing water, resists UV without turning brittle, and lasts longest of the two.
• Acrylic: the pick for roofs that drain clean. Lower cost per square, excellent reflectivity, and easy to recoat later.
• Both go down seamless, so there are no laps or fasteners for water to work into.
• Both drop the roof surface temperature sharply, which shows up on the cooling bill of a conditioned building.

When coating is the wrong call

If we find saturated insulation or a failing deck on your Sylmar roof, we say so. Coating over a wet roof traps the water and costs you twice.

How long a Sylmar roof coating lasts

A silicone system at the right thickness over a properly prepped roof gives you ten years and up, and acrylic is close behind on a roof that drains well. Both systems are renewable: when the time comes you wash the roof and add another coat instead of starting over, which is why building owners keep coming back to them.

The cost side of coating

Coating is priced by the square foot once we know the condition and how much prep the roof needs, and the number comes to you in writing before anything starts.

A coating runs well under the cost of a tear-off and replacement, and there is no dumpster, no demolition and no days of noise over the tenants' heads.

When coating makes sense in Sylmar

Good candidates for coating tend to have:

• Seams and laps that have opened up and started weeping
• A building that cooks in summer and runs the air conditioning hard
• A roof with years left in the deck and insulation underneath
• Flashing and penetrations that leak while the field of the roof is still solid
• Chalky, sun-baked membrane that has lost its surface but not its body

Get a Sylmar roof coating estimate

The estimate is free. Call (818) 275-0921 and we will measure your Sylmar roof, check the deck, seams and drains, and tell you plainly whether coating is the right call.