ROOF COATINGSilicone & Acrylic

Most Culver City flat roofs do not need tearing off — they need cleaning, repairing and sealing. Hot, dry summers and sharp swings between day and night work the membrane and its laps until the surface gives up.

Lifespan and recoating

A silicone system at the right thickness over a properly prepped roof gives you ten years and up, and acrylic is close behind on a roof that drains well. Both systems are renewable: when the time comes you wash the roof and add another coat instead of starting over, which is why building owners keep coming back to them.

Does your Culver City roof need coating?

We usually recommend coating when the roof shows:

• A roof with years left in the deck and insulation underneath
• Low spots that hold water for days after a storm
• Seams and laps that have opened up and started weeping
• Chalky, sun-baked membrane that has lost its surface but not its body
• A building that cooks in summer and runs the air conditioning hard

What changes on a Culver City roof

The short version for Culver City: summer radiant heat is the single biggest ager of roofs here. Our shop sits about 9 miles west of Culver City, so a crew is on site the same morning.

We are in West Los Angeles, Beverly Hills and Inglewood constantly, and the housing stock is much the same.

• Access gets planned first - driveway, staging, dumpster placement - so the street stays usable.
• We protect landscaping and the pool before a single bundle comes off the truck.
• Gutters are pulled and refitted where they block a proper drip edge.
• Dry-in happens the same day the old roof comes off; nothing sits open overnight.
• Satellite dishes and A/C line sets are re-flashed, not just set back down.

The first big storm books out the whole trade, so earlier is cheaper. Ask for the inspection, keep the report, and decide in your own time.

What you can expect from us

Weather delays are called early rather than left to surprise you.

• Ventilation gets looked at while the roof is open; most Culver City attics run hotter than they should.
• The site is cleaned daily, and the last magnet pass happens before the crew leaves.
• Keep the paperwork: it transfers if you sell the house.
• Synthetic underlayment goes down over the whole deck, not just the valleys.

Silicone or acrylic for a Culver City roof?

• Silicone: the pick for roofs that pond. It handles standing water, resists UV without turning brittle, and lasts longest of the two.
• Acrylic: the pick for roofs that drain clean. Lower cost per square, excellent reflectivity, and easy to recoat later.
• Both go down seamless, so there are no laps or fasteners for water to work into.
• Both drop the roof surface temperature sharply, which shows up on the cooling bill of a conditioned building.

When coating is the wrong call

If we find saturated insulation or a failing deck on your Culver City roof, we say so. Coating over a wet roof traps the water and costs you twice.

What roof coating costs in Culver City

Coating is priced by the square foot once we know the condition and how much prep the roof needs, and the number comes to you in writing before anything starts.

Because the work is additive, most buildings stay open and in use while we are on the roof.

What the work looks like

• Inspect and measure, including core tests where we need to know what is under the membrane
• Clean the roof — power wash, remove dirt, chalk and loose coating
• Repair: cracks, open seams, failed flashing, blisters and bad penetrations
• Prime where the substrate calls for it
• Apply the coating in multiple passes to the specified thickness, seams and details first
• Final walk for even coverage and thickness, then clean up the site

Serving Culver City and nearby

We coat commercial and residential low-slope roofs throughout Culver City and the surrounding Los Angeles County communities, including West Los Angeles, Beverly Hills and Inglewood.

Ready to look at your roof

The estimate is free. Call (818) 275-0921 and we will measure your Culver City roof, check the deck, seams and drains, and tell you plainly whether coating is the right call.